How to install a garden hose reel on a wall

A wall-mounted hose reel keeps the hose off the ground, protects it from ultraviolet damage and makes it quicker to reach the tap before a warm day. It also stops a wet coil from becoming a trip hazard across a path. Mounted at a sensible height, the drum can sit within easy reach while the hose feeds directly towards the beds, lawn or vegetable patch.

The installation is straightforward when the bracket, wall anchors and tap fittings suit the location. Solid brick and concrete walls are ideal, but timber frames, plasterboard panels and Colorbond fences need a different approach. Choosing the mounting position before buying anything helps avoid mismatched hardware, unnecessary drilling and a hose that does not reach where it is needed.

Choose a position that works

Start by following the water pipe from your outdoor tap. The reel should be close enough for the inlet hose to connect without a tight bend, yet far enough to keep the garden hose away from doors, windows and busy walkways. Check the direction in which the hose unwinds, as a side-facing hose guide usually pulls out more smoothly than one pointing towards the wall.

Choose a height that suits the household rather than simply placing the unit as high as possible. A mounting point around chest height is convenient for most people, but a fixed-drum reel may be easier to use from a lower position. Consider children, older adults and anyone who may struggle to lift a heavy hose. Make sure the tap remains accessible for shutting off the water and changing fittings.

Council rules can influence where and when you use the hose. Depending on the current restrictions in Sydney, Melbourne, Brisbane or Perth, handheld watering may be limited to particular hours or suspended during severe weather or declared restrictions. Schedule watering around those conditions, and avoid positioning the reel where its hose would run across a neighbour’s path or a shared driveway.

Match the reel to your wall

Choose between a fixed drum, a spring-loaded retractable reel and a simple wall-mounted hose holder. A fixed model is durable and economical, while a retractable unit is convenient where the hose is used frequently. Check the stated hose capacity, diameter and working pressure before buying. Many Australian households use either 12 mm or 19 mm hose, and a reel designed for a narrower hose may restrict flow.

Identify the wall material before selecting fixings. Brick, concrete blocks, solid timber and concrete panels can usually carry a reel, provided the correct anchors are used. Plasterboard needs suitable hollow-wall anchors, and a fence needs a structural post rather than the thin cladding alone. Older suburban homes often have brick rear walls, while modern yards frequently use treated timber or Colorbond fencing, so the same mounting method will not suit every property.

Measure the available space, including the swing of the reel, the hose guide and the swivel connection. Leave room to operate the handle without striking a window or door. Australian hardware retailers such as Bunnings, Mitre 10 and Total Tools carry several styles of wall brackets, but the included screws may only be suitable for timber. Buy anchors separately if the wall requires them.

Prepare the outdoor tap

Turn off the water at the isolation valve before removing any existing connector from the outdoor tap. A separate valve close to the reel makes servicing much easier, particularly if the isolation valve is hidden near the house. Fit the tap adaptor or hose bib required by the reel, using thread sealant tape on the tapered threads where it is suitable. Do not apply tape to a compression nut, which seals against a clean, flat face instead.

Inspect the threads for damage and check that the washer is in good condition. Cracked or distorted washers are a common cause of leaking connections and may not be included with a new reel. If the existing hose thread does not match the adaptor, take it to the hardware store for comparison rather than forcing the parts together. Hand-tightening followed by a small additional turn is usually sufficient.

Open the tap briefly before attaching the reel so that any grit or fragments are flushed from the pipe. Confirm that the isolation valve works and that the tap does not drip when closed. If you intend to connect the reel to a pump or rainwater tank, check the reel manufacturer’s pressure and flow requirements first. A mains-fed garden setup should not be connected to a pump unless the unit is designed for that arrangement.

Mark, drill and secure the bracket

Hold the bracket template against the wall and mark the fixing holes with a pencil. Use a spirit level to keep the reel horizontal, and make sure the hose guide points in the intended direction. Locate studs, cables, pipes and damp areas before drilling. Avoid mortar joints in brick walls because the soft mortar can crumble and provide a weak fixing point.

Choose a drill bit that matches the anchor rather than simply copying the diameter of the bracket hole. Common masonry screws may need a 6 mm or 8 mm bit, but the instructions supplied with the anchor should determine the correct size and depth. Drill slightly deeper than the anchor requires, clear the dust with a brush or vacuum and insert the plugs carefully. A masonry hammer drill makes the job faster through brick or concrete.

Fit the bracket and tighten the fixings evenly. Do not overtighten the screws, as this can damage the bracket, strip the thread in the anchor or crush the face of a brick. Two well-spaced anchors distribute the load better than one, especially when the drum contains water. Follow the weight rating and spacing specified by the reel manufacturer, and never use ordinary plasterboard screws in a hollow wall.

Attach the reel and connect the hose

Assemble the drum, guide and outlet according to the manufacturer’s instructions. Secure the garden hose to the drum with the supplied hose clamp, tightening it firmly enough to prevent slipping without crushing the hose. Route the hose onto the drum in even layers, following any arrows or winding diagrams. A tidy winding reduces tangles and helps the reel retract evenly.

Connect the inlet to the outdoor tap, making sure that any washers are correctly seated. A swivel joint between the tap and the reel allows the drum to turn without twisting the supply hose. The outlet connection should also turn freely, and the hose should leave the guide in a straight line rather than curving sharply downwards. Sharp bends are a frequent source of kinks and premature wear.

Open the isolation valve slowly and watch every connection while the water pressure builds. Check the tap adaptor, inlet hose, swivel, drum and outlet for dripping. A small amount of water may escape while the hose settles onto the drum, but a steady leak requires another washer or a tighter connection. Do not overtighten a leaking plastic fitting; replace the faulty seal instead.

Test, maintain and use it safely

Pull the hose out to its full working length and let it retract, checking that it winds evenly without catching. For a spring-loaded model, the hose should retract smoothly to its holder without the drum striking the wall. Test the locking mechanism and ensure the hose guide does not rub against the bracket. If the reel moves or twists, stop using it until the fixings have been checked.

Rinse the hose after use and let it dry before winding it in, particularly after applying fertiliser or other garden products. Clean the inlet filter if the model has one, and replace worn washers before they create leaks. Moving parts can be lightly lubricated with a suitable product, but follow the manual because some plastics and seals are damaged by petroleum-based lubricants. Store the unit closed and protected from direct summer sun where possible.

Salt-laden air near the coast can corrode exposed metal, so inspect fittings regularly in places such as Sydney or Perth. In inland areas, high summer temperatures can make a metal drum hot to the touch. Never use the reel or its bracket as a step, and keep children away from a spring-loaded hose under tension. Automatic timers and irrigation systems must also follow local watering restrictions rather than bypassing them.


Choose the location, gather the correct anchors and fittings, and install the reel this weekend. A securely mounted unit will keep the hose protected, the path clearer and everyday watering far more convenient across the garden.